Empire P)-1 Owner's Manual download pdf (Page 27)

29210-0-0911 Page 27

InstallationofVerticalInletBafe

The vertical inlet bafe is to be used only in a completely vertical vent

installation. The vertical inlet bafe can be used when the vertical

vent rise is between 10 feet and 40 feet. To maintain the yellow

ame in the main burner, purchase Vertical Inlet bafe, DVF-139

from your Empire Comfort Systems, Inc. distributor or dealer for

Simpson Duravent only.

In a vertical vent rise the ame on the main burner can be reduced

due to the drawing action from the ue exhaust pipe and the air inlet

pipe. A decrease in the height or the appearance of the yellow ame

may occur when the vertical vent rise is between 10 feet and 40 feet.

To enhance the yellow ame on the main burner, the vertical inlet

bafe can be attached to the direct vent high wind vertical top.

Please use the following steps to install the vertical inlet

bafe.

1. Place the vertical inlet bafe over the exterior of the air inlet

openings on the direct vent high wind vertical top.

2. There are three sections of air openings on the exterior of the

air inlet pipe.

To achieve the maximum amount of yellow ame the vertical

inlet bafe will cover-up three sections of air openings.

To achieve the minimum amount of yellow ame the vertical

inlet bafe will cover-up one section of air openings.

3. Attach vertical inlet bafe to the direct vent high wind vertical

top with (2) 3/8" hex-head screws provided with vertical inlet

bafe.

4. Installation of vertical inlet bafe is completed.

Parts List

Description

Part

Number

Quantity

Supplied

Vertical Inlet Bafe DVF-139 1

3/8" Hex-Head Screw R-2656 2

ReassemblyandResealingVentPipeSystem

Attach vent pipe to inlet and outlet vent adaptor on replace. Replace

the horizontal and vertical pipe lengths, elbows and horizontal or

vertical termination kit.

All vent system components lock into place by sliding the concentric

pipe section with four (4) equally spaced interior beads onto the

appliance collar or previously installed component end with four

(4) equally spaced indented sections. When the internal beads of

each starting outer pipe line up, rotate pipe section clockwise 90°

(approximately 3 inches). The vent pipe is now locked together.

Continue replacing components per the vent system conguration.

Be certain that each succeeding vent component is securely tted

and locked into the preceding component in the vent system.

ReassemblyandResealingGasAccumulationReliefSystem

GlassFrameAssemblyandCombustionChamber

Whenever the glass frame assembly is pivoted open by a delayed

ignition in the main burner, the glass frame assembly gaskets and

combustion chamber must be examined by a qualied service person

for damage. All damaged gaskets on the glass frame assembly and

combustion chamber must be replaced by a qualied service person.

If damage occurs to the combustion chamber, it must be replaced

by a qualied service person. Contact Empire Comfort Systems,

Inc. for replacement parts.

VerticalThroughtheRoofApplications(Figure38)

Your Gas Fireplace has been approved for:

a) Vertical installations up to 40 feet in height.

b) Two sets of 45 degree elbow offsets within these vertical

installations. From 0 to a maximum of 8 ft. a vent pipe can be

used between elbows.

c) Wall straps must be used to support offset pipe every 4'.

This application will require that you rst determine the roof pitch

and use the appropriate venting components.

24”MINIMUM

CLEARANCE TO

COMBUSTIBLES;

NATURAL OR

MAN MADE.

TYPICAL ROOF

SUPPORT

TYPICAL JOIST

SUPPORT

40’

(12.19 M)

MAXIMUM

8’ (2.44 M)

MAXIMUM

8’ (2.44 M)

MAXIMUM

45°

Figure38

VERTICALTERMINATION(continued)

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 47 48

Comments to this Manuals

No comments

Empire P)-1 Owner's Manual Page 27

Comments to this Manuals

Related products and manuals for Fireplaces Empire P)-1